← Collection and preparation guide
Get ready to discover.
Dry ice is solid carbon dioxide, about -78.5°C. At normal air pressure it changes directly into gas. The teacher handles it; students observe, predict, measure and explain.
Gather the basics
Insulated gloves • Tongs • Safety goggles • Vented insulated storage • Trays • A well-ventilated demonstration space. Each page lists its extra equipment.
Before class, try the chosen demonstration and set up where students can see without reaching the dry ice.
Colour-changing cabbage water
Watch a colour change as CO₂ dissolves and changes the water’s acidity.
You Will Need
473. mL plastic cup • Water • Red cabbage juice • Small dry ice pieces. To prepare the juice: two red cabbage leaves, saucepan and strainer.
How To Do It
1. Prepare the indicator ahead of class: tear the leaves, cover with water, simmer while stirring, then strain and cool the purple liquid.
2. Fill the cup almost to the top with water. Stir in 5 mL cabbage juice and show the starting colour.
3. The teacher adds a few small dry ice pieces with tongs. Observe the colour as the liquid bubbles.
Explore A Different Effect
Replace the cabbage juice with 5 mL universal indicator. Observe the colour change using the same procedure.
What’s Happening?
Dissolved CO₂ forms carbonic acid. The cabbage pigment responds to the lower pH by changing colour; this is a chemical effect, not simply cooling.
Ask The Class
What evidence suggests the liquid’s chemistry changed?
Activity reference: Steve Spangler - open the published instructions
One giant bubble
Grow a soap dome filled with fog, then watch it burst.
You Will Need
Smooth-rimmed plastic bowl under 30 cm wide • Warm water • Dish soap • Small cup • Cloth strip, 2.5 cm x 46 cm • Dry ice.
How To Do It
1. Half-fill the bowl with warm water. In the cup, mix 30 mL dish soap with 15 mL water and soak the cloth.
2. The teacher adds two or three dry ice pieces to the bowl. Wet the rim with bubble solution.
3. Stretch the soapy cloth between your hands and draw it slowly across the rim to leave a soap film. Watch the dome grow and burst.
Explore A Different Effect
Illuminate the bubble with a waterproof light to see the fog moving inside. Keep the light suitable for use in water.
What’s Happening?
Gas fills the soap film and makes it expand. Tiny water droplets make the fog inside visible.
Ask The Class
Why does the bubble grow after the cloth has been removed?
Activity reference: Steve Spangler - open the published instructions
Overflowing bubbles
Watch fog-filled foam build up and spill over the container.
You Will Need
Open plastic bowl or cylinder • Warm water • Liquid dish soap • Dry ice • Tray.
How To Do It
1. Half-fill the container with warm water and add a few drops of dish soap.
2. The teacher lowers a small dry ice piece into the water with tongs.
3. Watch foam rise and spill onto the tray. Let the bubbles burst; keep hands out of the container.
What’s Happening?
Soap films trap escaping carbon dioxide and fog. New bubbles push the foam upward and over the rim.
Ask The Class
What changes when soap is added to the warm-water demonstration?
Activity reference: Steve Spangler - open the published instructions
Individual fog-filled bubbles
Use a bubble generator to make separate bubbles filled with fog.
You Will Need
3.8 L plastic jar • 90 cm tubing • Drill • Small funnel • Warm water • Soap • Small cup • Dry ice • Knit gloves for the variation.
How To Do It
1. Attach tubing through a hole near the jar’s top and a funnel at the free end. Keep the outlet clear.
2. Half-fill with warm water and add dry ice. Mix soap into 120 mL water in the small cup.
3. Wet the funnel in soap solution. Hold the lid loosely on the jar to direct fog through the tube; never screw it shut.
4. Grow a bubble and shake it free. Lift the lid if the outlet stops flowing.
Explore A Different Effect
Catch or gently bounce bubbles on clean knit gloves or a towel. These fabrics do not protect hands from dry ice; only the teacher handles the ice.
What’s Happening?
The soap film encloses fog and CO₂. When the film breaks, the fog escapes.
Ask The Class
Which fabric helps a bubble survive contact?
Activity reference: Steve Spangler - open the published instructions
Build a fog-ring launcher
Build a cup launcher and tap its membrane to send rings through the air.
You Will Need
473. mL plastic cup • Freezer bag • Rubber bands • 25 mm coin • Marker • Scissors or knife • 60 mL warm water • 1-2 small dry ice pieces.
How To Do It
1. The teacher traces the coin on the centre of the cup’s base and cuts a smooth 25 mm hole.
2. Stretch freezer-bag plastic over the large opening. Secure with rubber bands and trim excess, leaving enough plastic to pull snug.
3. Add 60 mL warm, not hot, water through the hole, then add small dry ice pieces with insulated gloves.
4. Hold the plastic towards you and the hole away from people. Tilt slightly so the water rests against the plastic.
5. Lightly tap the plastic to send rings out. Keep the hole open so gas can escape.
What’s Happening?
Air leaving a round opening curls into a rolling ring. Fog makes that air movement visible.
Ask The Class
How does a gentle tap compare with a firmer tap?
Activity reference: Steve Spangler - open the published instructions
Make a fog tornado
Create a spinning column above a container of fog.
You Will Need
Shallow tub • Warm water • Dry ice pellets • Dark table covering.
How To Do It
1. Set the tub on the covered table. The teacher adds dry ice to warm water to create fog.
2. Hold a hand flat and upright in the fog outside the tub, away from the ice and water. Lift it quickly.
3. Watch for a short-lived rotating column; repeat to practise the motion.
What’s Happening?
Moving air can spin into a vortex. The fog reveals its shape.
Ask The Class
What movement produces the clearest rotating column?
Activity reference: Ingrid Sulston - open the published instructions
Horizontal fog vortices
Use a bottle to direct spinning fog sideways and model air movement.
You Will Need
Flexible plastic water bottle with its cap removed • A little warm water • Dry ice pellet.
How To Do It
1. The teacher adds a little warm water and one pellet to the uncapped bottle.
2. Let the strongest bubbling settle. Point the opening away from people.
3. Gently squeeze and release the bottle quickly. Keep the mouth open throughout.
What’s Happening?
A pulse of fog reveals a rolling air vortex moving sideways.
Ask The Class
Compare the visible motion with the cup launcher’s rings.
Activity reference: Ingrid Sulston - open the published instructions
Watch the fog roll
Observe bubbling water and a cloud of tiny water droplets.
You Will Need
Open plastic bowl or cylinder • Warm water • Dry ice pellets • Tray.
How To Do It
1. Put warm water in the open container and place it on a tray.
2. The teacher adds dry ice using tongs. Observe bubbles and fog without leaning over the vessel.
3. Watch how the effect changes as the water cools and the solid gets smaller.
Explore A Different Effect
Repeat with equal water volumes at two measured starting temperatures and comparable dry ice pieces. Record the difference in bubbling and fog.
What’s Happening?
Heat enters the dry ice and it becomes CO₂ gas. Cold gas cools water vapour into tiny droplets: the visible fog.
Ask The Class
Is the white cloud the carbon dioxide itself, or something made visible by cooling?
Activity reference: Science Friday - open the published instructions
Graph the cooling water
Measure water temperature over time and plot the results.
You Will Need
Open beaker • Room-temperature water • Thermometer • Timer • Dry ice • Graph paper.
How To Do It
1. Record the water’s starting temperature. The teacher adds dry ice.
2. Measure the water temperature every minute and record each reading.
3. Plot time horizontally and temperature vertically. Describe the curve.
What’s Happening?
Heat transfers from the water to the colder dry ice.
Ask The Class
Where does the temperature change fastest?
Activity reference: Science Friday - open the published instructions
Disappearing dry ice
Observe a solid getting smaller as it changes directly into gas.
You Will Need
Co₂
Small dry ice piece • Open insulated support • Timer • Observation sheet.
How To Do It
1. The teacher places the piece on the support, out of students’ reach.
2. Sketch its starting shape. Observe at regular intervals without moving it.
3. Compare later sketches with the first and describe what remains.
What’s Happening?
At normal air pressure, dry ice changes directly from solid carbon dioxide to gas. This change is sublimation.
Ask The Class
Where has the material gone when the solid is no longer visible?
Activity reference: Science Friday - open the published instructions
Does piece size matter?
Investigate how size and exposed surface area affect sublimation.
You Will Need
Co₂
Dry ice pieces of different sizes • Two matching open containers • Balance • Timer • Results sheet.
How To Do It
1. Plan a fair test: compare equal starting masses arranged as one larger piece and several smaller pieces. The teacher weighs and places the ice.
2. Keep both containers in the same conditions. Record their masses at matching times.
3. Compare mass loss and explain which variables were controlled.
What’s Happening?
This investigation tests how exposed surface area affects heat transfer and sublimation. Compare measured results rather than judging fog alone.
Ask The Class
What would make this an unfair comparison?
Activity reference: Science Friday - open the published instructions
Make a spoon sing
Listen as escaping gas makes a metal spoon vibrate.
You Will Need
Metal spoon • Dry ice piece with a flat surface • Insulated support.
How To Do It
1. The teacher places the dry ice on the support.
2. Hold the spoon by its handle and press its bowl gently against the dry ice. Listen for vibration.
3. As the spoon cools, compare the sound. Let it warm before repeating.
Explore A Different Effect
After cooling the spoon, observe frost appearing on it. Moisture from the air forms ice on the cold metal.
What’s Happening?
Heat from the spoon speeds sublimation. Escaping gas makes the metal vibrate and produces sound.
Ask The Class
How does the spoon’s temperature affect the sound?
Activity reference: Ingrid Sulston - open the published instructions
Make a coin dance
Watch a coin rock back and forth as gas escapes around it.
You Will Need
Coin • Dry ice with a flat surface • Open support.
How To Do It
1. The teacher places the dry ice on the support.
2. Using insulated gloves, press the coin’s edge into the dry ice so it stands upright.
3. Release and watch for rocking motion. Keep students’ hands away from the demonstration.
What’s Happening?
The warmer coin transfers heat into dry ice; escaping gas can push the coin from side to side.
Ask The Class
What connects this movement with the singing spoon?
Activity reference: Ingrid Sulston - open the published instructions
Gliding dry ice
Watch a piece move on a cushion of escaping gas.
You Will Need
Co₂
Flat dry ice piece • Smooth, level demonstration surface with room to move.
How To Do It
1. The teacher places the piece on the surface using insulated gloves.
2. Give it a gentle push, keeping it on the demonstration area.
3. Observe how it moves and ask students to explain the small gap underneath.
What’s Happening?
Rapid sublimation creates a layer of gas beneath the solid. That gas cushion reduces contact with the surface.
Ask The Class
What would you expect on a rougher surface?
Activity reference: University of Colorado - open the published instructions
Freeze a little water
Observe dry ice turning a small amount of liquid water into ice.
You Will Need
Co₂
Dry ice piece • Dropper • Water • Cold-tolerant demonstration surface.
How To Do It
1. Put several drops of water on the surface.
2. The teacher moves dry ice into the small puddle using tongs.
3. After about three minutes, move the dry ice aside and observe the frozen water.
What’s Happening?
Water loses heat to the much colder dry ice and freezes. Freezing water and sublimating CO₂ are different state changes.
Ask The Class
Which substance became a gas, and which became a solid?
Activity reference: AACT - open the published instructions
Change a ball’s bounce
Compare the bounce of special polymer balls before and after cooling.
You Will Need
“Happy and sad” polymer demonstration balls • Dry ice cooling container, left vented • Tongs • Ruler • Firm drop surface.
How To Do It
1. Drop both balls from the same measured height at room temperature. Record the bounce heights.
2. The teacher cools the balls using dry ice, then removes them with tongs.
3. Repeat the drops from the same height. Compare with the starting results.
What’s Happening?
The balls use different polymers. Their ability to return energy in a bounce changes with temperature; cooling reduces their bounce.
Ask The Class
Why must the drop height stay the same?
Activity reference: Indiana University - open the published instructions
Extinguish a candle with CO₂
See carbon dioxide displace air around a flame and put it out.
You Will Need
Four tea lights • Clear open tank • Inverted jars or beakers of different heights • Plastic pitcher • Dry ice • Long lighter.
How To Do It
1. Arrange the inverted vessels as platforms at different heights in the tank, with one tea light on each.
2. The teacher places dry ice in the open pitcher and waits about ten minutes for CO₂ to collect.
3. Keep flammables away. The teacher lights the candles, then slowly tips gas into the tank, retaining all solid dry ice in the pitcher.
4. Observe which flame goes out first and the order that follows.
What’s Happening?
CO₂ does not sustain the candle flames and is denser than the surrounding air. The lower flames are extinguished first.
Ask The Class
How does the order of extinction reveal something about the invisible gas?
Activity reference: Rutgers University - open the published instructions
Calculate CO₂’s molar mass
Use gas measurements and gas laws to identify the substance.
You Will Need
Pv
nRT
250. mL Erlenmeyer flask and stopper • Analytical balance • Thermometer • Graduated cylinder • Timer • Atmospheric pressure reading • Dry ice.
How To Do It
1. Record pressure and the mass of the dry flask plus stopper. Remove the stopper; the teacher adds a small dry ice piece.
2. Leave the flask OPEN until all solid has sublimed. Wait three more minutes; measure gas temperature.
3. Only after all dry ice is gone, stopper and weigh the flask. Empty the gas and repeat a trial.
4. Measure actual flask volume using water filled to the stopper position, then measure that water in a graduated cylinder.
What’s Happening?
Calculate n = PV / RT with consistent units. Correct the mass difference for displaced air: m(CO₂) = mass difference + air density x flask volume. Then M = m / n. AACT uses 1.29 g/L for its air-density approximation.
Ask The Class
How would using the nominal flask volume instead of its measured volume affect the result?
Activity reference: AACT - open the published instructions
Build a cloud chamber
Use dry ice to cool a detector that reveals particle tracks.
You Will Need
Clear tank • Felt • Alcohol-resistant glue • Black metal base plate • Tape • Open dry ice tray • Bright light • Isopropyl alcohol.
How To Do It
1. Attach felt inside the tank near its base. Prepare a close-fitting black metal plate for the tank’s open rim.
2. In ventilation, away from flames, soak the felt with isopropyl alcohol without leaving it dripping. Invert the tank onto the plate and tape the rim joint.
3. Place the plate on a level layer of dry ice in the OPEN tray. Dry ice stays outside the chamber.
4. Wait about ten minutes. Keep the chamber’s top at room temperature and shine a bright light across the cold base at a low angle. Look for brief tracks.
What’s Happening?
Alcohol vapour becomes supersaturated near the cold base. Charged particles leave ions that trigger tiny droplets, revealing their paths.
Ask The Class
How is a track different from the background falling droplets?
Activity reference: Science in School - open the published instructions
Shake up your own ice cream.
Mix your flavour. Shake it up. Add your favourite toppings.
You Will Need
Two small resealable food bags • Breathable outer bag that keeps the dry ice contained • Dry ice • Bowl • Spoon • ½ cup milk • ½ cup cream • Chocolate or strawberry topping.
How To Do It
1. Students mix the milk, cream and topping. Pour into a small food bag, squeeze out the air and seal. Place it inside the second small bag and seal that too.
2. Place the sealed food bags inside the outer bag, with dry ice around them. Use a breathable outer bag that keeps the dry ice contained. Dry ice stays outside the food bags.
3. Wear insulated gloves and shake the outer bag until the mixture is creamy.
4. Remove the food bags from the dry ice before opening and serving. Students add toppings. Discard the mixture if a bag splits or dry ice enters it.
What’s Happening?
Heat moves from the mixture through the bags to the colder dry ice. Shaking keeps the mixture moving as it freezes.
Ask The Class
How did the mixture’s texture change as it cooled?
Activity reference: Fizzics Education (adapted dry ice variation) - open the published instructions